CEN/TS 15862:2012
Current
The latest, up-to-date edition.
Characterisation of waste - Compliance leaching test - One stage batch leaching test for monoliths at fixed liquid to surface area ratio (L/A) for test portions with fixed minimum dimensions
18-07-2012
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Reagents
6 Equipment
7 Sample preparation
8 Procedure
9 Calculations and expression of results
10 Documentation and test report
11 Test performance
Annex A (informative) - Example of data sheet
showing the reporting of key elements
mentioned in CEN/TS 15862
Annex B (informative) - Examples of data about
the L/A ratio
Annex C (informative) - Examples of factors influencing
the leaching release of monolithic waste
Annex D (informative) - Process map for CEN/TS 15862
Bibliography
This document specifies a compliance test for routine testing providing information on the leaching of monolithic waste which can be obtained under the experimental conditions specified hereafter with a single batch leaching test at a specified liquid to surface area ratio (L/A) of 12 (cm3cm-2). It applies to test portion of monolithic waste of regular shape, with a minimum dimension of 40 mm in all directions, obtained e.g. by cutting, coring or moulding.This document is not applicable if the surface area of the test portion cannot be determined by simple geometrical means.This document has been developed to determine the release of mainly inorganic constituents from wastes. It does not take into account the particular characteristics of organic constituents nor the consequences of microbiological processes in organic degradable wastes.The test procedure specified in this document produces an eluate which subsequently need to be characterised physically and chemically, according to appropriate standard methods.NOTE 1If, in order to comply with the requirement of regular shape, the test portion is prepared by cutting or coring, then new surfaces are exposed which can lead to change(s) in leaching properties.NOTE 2This procedure may not be applicable to materials reacting with the leachant, leading for example to excessive gas emission or an excessive heat release.This leaching test does not provide information by itself on dynamic leaching behaviour, as specified in EN 12920. It does not give information on equilibrium conditions. For specific situations or basic characterization, other tests are available in the toolbox of CEN/TC 292 "Characterization of waste".This document does not address issues related to health and safety.
Committee |
CEN/TC 444
|
DocumentType |
Technical Specification
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Current
|
Standards | Relationship |
UNI CEN/TS 15862 : 2012 | Identical |
XP CEN/TS 15862 : 2012 XP | Identical |
S.R. CEN/TS 15862:2012 | Identical |
PD CEN/TS 15862:2012 | Identical |
DIN CEN/TS 15862;DIN SPEC 91233:2012-11 | Identical |
PNE-prEN 15862 | Identical |
DIN EN 15863:2015-06 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST FOR BASIC CHARACTERIZATION - DYNAMIC MONOLITHIC LEACHING TEST WITH PERIODIC LEACHANT RENEWAL, UNDER FIXED CONDITIONS |
EN 15863:2015 | Characterization of waste - Leaching behaviour test for basic characterization - Dynamic monolithic leaching test with periodic leachant renewal, under fixed conditions |
UNI EN 16457 : 2014 | CHARACTERIZATION OF WASTE - FRAMEWORK FOR THE PREPARATION AND APPLICATION OF A TESTING PROGRAMME - OBJECTIVES, PLANNING AND REPORT |
I.S. EN 16457:2014 | CHARACTERIZATION OF WASTE - FRAMEWORK FOR THE PREPARATION AND APPLICATION OF A TESTING PROGRAMME - OBJECTIVES, PLANNING AND REPORT |
UNE-EN 15863:2015 | Characterization of waste - Leaching behaviour test for basic characterization - Dynamic monolithic leaching test with periodic leachant renewal, under fixed conditions |
UNE-EN 15002:2015 | Characterization of waste - Preparation of test portions from the laboratory sample |
S.R. CEN/TS 15863:2012 | CHARACTERISATION OF WASTE - LEACHING BEHAVIOUR TEST FOR BASIC CHARACTERISATION - DYNAMIC MONOLITHIC LEACHING TEST WITH PERIODIC LEACHANT RENEWAL, UNDER FIXED TEST CONDITIONS |
I.S. EN 15002:2015 | CHARACTERIZATION OF WASTE - PREPARATION OF TEST PORTIONS FROM THE LABORATORY SAMPLE |
UNE-EN 16457:2014 | Characterization of waste - Framework for the preparation and application of a testing programme - Objectives, planning and report |
PD CEN/TS 15864:2012 | Characterisation of waste. Leaching behaviour test for basic characterisation. Dynamic monolithic leaching test with continuous leachant renewal under conditions relevant for specified scenario(s) |
I.S. EN 15863:2015 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST FOR BASIC CHARACTERIZATION - DYNAMIC MONOLITHIC LEACHING TEST WITH PERIODIC LEACHANT RENEWAL, UNDER FIXED CONDITIONS |
12/30263896 DC : 0 | BS EN 16457 - CHARACTERIZATION OF WASTE - FRAMEWORK FOR THE PREPARATION AND APPLICATION OF A TESTING PROGRAMME - OBJECTIVES, PLANNING AND REPORT |
DIN EN 16457:2014-07 | CHARACTERIZATION OF WASTE - FRAMEWORK FOR THE PREPARATION AND APPLICATION OF A TESTING PROGRAMME - OBJECTIVES, PLANNING AND REPORT |
S.R. CEN/TS 15864:2015 | CHARACTERISATION OF WASTE - LEACHING BEHAVIOUR TEST FOR BASIC CHARACTERIZATION - DYNAMIC MONOLITHIC LEACHING TEST WITH CONTINUOUS LEACHANT RENEWAL UNDER CONDITIONS RELEVANT FOR SPECIFIED SCENARIO(S) |
PD CEN/TS 15863:2012 | Characterisation of waste. Leaching behaviour test for basic characterisation. Dynamic monolithic leaching test with periodic leachant renewal, under fixed test conditions |
13/30291099 DC : 0 | BS EN 15002 - CHARACTERIZATION OF WASTE - PREPARATION OF TEST PORTIONS FROM THE LABORATORY SAMPLE |
BS EN 15863:2015 | Characterization of waste. Leaching behaviour test for basic characterization. Dynamic monolithic leaching test with periodic leachant renewal, under fixed conditions |
DIN EN 15002:2015-07 | CHARACTERIZATION OF WASTE - PREPARATION OF TEST PORTIONS FROM THE LABORATORY SAMPLE |
EN 15002:2015 | Characterization of waste - Preparation of test portions from the laboratory sample |
EN 16457:2014 | Characterization of waste - Framework for the preparation and application of a testing programme - Objectives, planning and report |
DIN EN 16457 E : 2014 | CHARACTERIZATION OF WASTE - FRAMEWORK FOR THE PREPARATION AND APPLICATION OF A TESTING PROGRAMME - OBJECTIVES, PLANNING AND REPORT |
BS EN 16457:2014 | Characterization of waste. Framework for the preparation and application of a testing programme. Objectives, planning and report |
13/30286655 DC : 0 | BS EN 15863 - CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST FOR BASIC CHARACTERIZATION - DYNAMIC MONOLITHIC LEACHING TEST WITH PERIODIC LEACHANT RENEWAL, UNDER FIXED TEST CONDITIONS |
BS EN 15002:2015 | Characterization of waste. Preparation of test portions from the laboratory sample |
CEN/TS 15864:2015 | Characterization of waste - Leaching behaviour test for basic characterization - Dynamic monolithic leaching test with continuous leachant renewal under conditions relevant for specified scenario(s) |
CEN/TS 15863:2012 | Characterisation of waste - Leaching behaviour test for basic characterisation - Dynamic monolithic leaching test with periodic leachant renewal, under fixed test conditions |
XP X31 211 : 2000 XP | WASTE - TEST FOR THE DETERMINATION OF THE LEACHABILITY OF A SOLID WASTE MATERIAL INITIALLY MASSIVE OR GENERATED BY A SOLIDIFICATION PROCESS |
CEN/TS 14429:2005 | Characterization of waste - Leaching behaviour tests - Influence of pH on leaching with initial acid/base addition |
NEN 7345 : 1995 | LEACHING CHARACTERISTICS OF SOLID EARTHY AND STONY BUILDING AND WASTE MATERIALS - LEACHING TESTS - DETERMINATION OF THE LEACHING OF INORGANIC COMPONENTS FROM BUILDINGS AND MONOLITIC WASTE MATERIALS WITH THE DIFFUSION TEST |
CEN/TS 15863:2012 | Characterisation of waste - Leaching behaviour test for basic characterisation - Dynamic monolithic leaching test with periodic leachant renewal, under fixed test conditions |
CEN/TS 14997 : 2006 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TESTS - INFLUENCE OF PH ON LEACHING WITH CONTINUOUS PH-CONTROL |
EN 14346:2006 | CHARACTERIZATION OF WASTE - CALCULATION OF DRY MATTER BY DETERMINATION OF DRY RESIDUE OR WATER CONTENT |
ISO 5667-3:2012 | Water quality Sampling Part 3: Preservation and handling of water samples |
CEN/TS 15864:2015 | Characterization of waste - Leaching behaviour test for basic characterization - Dynamic monolithic leaching test with continuous leachant renewal under conditions relevant for specified scenario(s) |
EN 12457-1:2002 | Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 1: One stage batch test at a liquid to solid ratio of 2 l/kg for materials with high solid content and with particle size below 4 mm (without or with size reduction) |
EN 16192:2011 | Characterization of waste - Analysis of eluates |
EN ISO 5667-3:2012 | Water quality - Sampling - Part 3: Preservation and handling of water samples (ISO 5667-3:2012) |
ISO 3696:1987 | Water for analytical laboratory use — Specification and test methods |
EN 12920:2006+A1:2008 | Characterization of waste - Methodology for the determination of the leaching behaviour of waste under specified conditions |
EN ISO 3696:1995 | Water for analytical laboratory use - Specification and test methods (ISO 3696:1987) |
EN 15002:2015 | Characterization of waste - Preparation of test portions from the laboratory sample |
CEN/TS 14405 : 2004 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TESTS - UP-FLOW PERCOLATION TEST (UNDER SPECIFIED CONDITIONS) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.