• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 16192:2011

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Characterization of waste - Analysis of eluates
Superseded date

16-03-2022

Published date

23-11-2011

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Sample pretreatment
5 Blank determination
6 Interference
7 Selection of the suitable test method
8 Expression of results
9 Test report
Annex A (informative) - Validation of EN 12506:2003 and
        EN 13370:2003
Annex B (informative) - Additional validation data
Bibliography

This European Standard specifies methods for the determination of the parameters pH, ammonium, AOX, As, Ba, Cd, Cl-, easily liberatable CN-, Co, Cr, Cr(VI), Cu, DOC/TOC, electrical conductivity, F-, Hg, Mo, Ni, NO2-, Pb, phenol index, total S, Sb, Se, SO42-, TDS, V and Zn in aqueous eluates for the characterization of waste.

Committee
CEN/TC 444
DevelopmentNote
Supersedes PREN 16192, EN 12506 & EN 13370. (12/2011)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
NBN EN 16192 : 2012 Identical
SN EN 16192 : 2012 Identical
UNI EN 16192 : 2012 Identical
DIN EN 16192:2012-02 Identical
NEN EN 16192 : 2011 Identical
NF EN 16192 : 2012 Identical
NS EN 16192 : 2011 Identical
PN EN 16192 : 2012 Identical
UNE-EN 16192:2012 Identical
BS EN 16192:2011 Identical
I.S. EN 16192:2011 Identical

IEC 62561-7:2018 Lightning protection system components (LPSC) - Part 7: Requirements for earthing enhancing compounds
UNE-EN 14429:2015 Characterization of waste - Leaching behaviour test - Influence of pH on leaching with initial acid/base addition
BS EN 14405:2017 Characterization of waste - Leaching behaviour test - Up-flow percolation test (under specified conditions)
14/30304804 DC : 0 BS EN 14405 - CHARACTERISATION OF WASTE - LEACHING BEHAVIOUR TEST - UP-FLOW PERCOLATION TEST (UNDER SPECIFIED CONDITIONS)
17/30354239 DC : 0 BS EN 13369 - COMMON RULES FOR PRECAST CONCRETE PRODUCTS
DIN EN 15863:2015-06 CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST FOR BASIC CHARACTERIZATION - DYNAMIC MONOLITHIC LEACHING TEST WITH PERIODIC LEACHANT RENEWAL, UNDER FIXED CONDITIONS
UNE-EN 16123:2013 Characterization of waste - Guidance on selection and application of screening methods
EN 14997:2015 Characterization of waste - Leaching behaviour test - Influence of pH on leaching with continuous pH control
CEN/TS 15862:2012 Characterisation of waste - Compliance leaching test - One stage batch leaching test for monoliths at fixed liquid to surface area ratio (L/A) for test portions with fixed minimum dimensions
EN 14405:2017 Characterization of waste - Leaching behaviour test - Up-flow percolation test (under specified conditions)
CEN/TS 16637-3:2016 Construction products - Assessment of release of dangerous substances - Part 3: Horizontal up-flow percolation test
EN 15863:2015 Characterization of waste - Leaching behaviour test for basic characterization - Dynamic monolithic leaching test with periodic leachant renewal, under fixed conditions
CEN/TS 16637-2:2014 Construction products - Assessment of release of dangerous substances - Part 2: Horizontal dynamic surface leaching test
DIN EN 14997:2015-05 CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH CONTINUOUS PH CONTROL
UNI EN 16457 : 2014 CHARACTERIZATION OF WASTE - FRAMEWORK FOR THE PREPARATION AND APPLICATION OF A TESTING PROGRAMME - OBJECTIVES, PLANNING AND REPORT
DIN EN 14405 E : 2017 CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - UP-FLOW PERCOLATION TEST (UNDER SPECIFIED CONDITIONS)
UNI EN 13369 : 2013 COMMON RULES FOR PRECAST CONCRETE PRODUCTS
PREN 14429 : DRAFT 2013 CHARACTERISATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH INITIAL ACID/BASE ADDITION
EN IEC 62561-7:2018 Lightning protection system components (LPSC) - Part 7: Requirements for earthing enhancing compounds
BS EN 13369:2013 Common rules for precast concrete products
I.S. EN 16457:2014 CHARACTERIZATION OF WASTE - FRAMEWORK FOR THE PREPARATION AND APPLICATION OF A TESTING PROGRAMME - OBJECTIVES, PLANNING AND REPORT
PREN 14405 : DRAFT 2014 CHARACTERISATION OF WASTE - LEACHING BEHAVIOUR TEST - UP-FLOW PERCOLATION TEST (UNDER SPECIFIED CONDITIONS)
UNE-EN 14405:2017 Characterization of waste - Leaching behaviour test - Up-flow percolation test (under specified conditions)
I.S. EN 16123:2013 CHARACTERIZATION OF WASTE - GUIDANCE ON SELECTION AND APPLICATION OF SCREENING METHODS
UNI EN 16123 : 2013 CHARACTERIZATION OF WASTE - GUIDANCE ON SELECTION AND APPLICATION OF SCREENING METHODS
DIN EN 15863 E : 2015 CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST FOR BASIC CHARACTERIZATION - DYNAMIC MONOLITHIC LEACHING TEST WITH PERIODIC LEACHANT RENEWAL, UNDER FIXED CONDITIONS
17/30348303 DC : 0 BS EN 17087 - CONSTRUCTION PRODUCTS - ASSESSMENT OF RELEASE OF DANGEROUS SUBSTANCES - PREPARATION OF TEST PORTIONS FROM THE LABORATORY SAMPLE FOR TESTING OF RELEASE AND ANALYSIS OF CONTENT
UNE-EN 15863:2015 Characterization of waste - Leaching behaviour test for basic characterization - Dynamic monolithic leaching test with periodic leachant renewal, under fixed conditions
UNE-EN 15002:2015 Characterization of waste - Preparation of test portions from the laboratory sample
S.R. CEN/TS 15863:2012 CHARACTERISATION OF WASTE - LEACHING BEHAVIOUR TEST FOR BASIC CHARACTERISATION - DYNAMIC MONOLITHIC LEACHING TEST WITH PERIODIC LEACHANT RENEWAL, UNDER FIXED TEST CONDITIONS
I.S. EN 15002:2015 CHARACTERIZATION OF WASTE - PREPARATION OF TEST PORTIONS FROM THE LABORATORY SAMPLE
S.R. CEN/TS 15862:2012 CHARACTERISATION OF WASTE - COMPLIANCE LEACHING TEST - ONE STAGE BATCH LEACHING TEST FOR MONOLITHS AT FIXED LIQUID TO SURFACE AREA RATIO (L/A) FOR TEST PORTIONS WITH FIXED MINIMUM DIMENSIONS
DIN EN 14429 E : 2015 CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH INITIAL ACID/BASE ADDITION
DIN EN 16123:2013-05 Characterization of waste - Guidance on selection and application of screening methods
BS EN 16123:2013 Characterization of waste. Guidance on selection and application of screening methods
UNE-EN 14997:2015 Characterization of waste - Leaching behaviour test - Influence of pH on leaching with continuous pH control
UNE-EN 16457:2014 Characterization of waste - Framework for the preparation and application of a testing programme - Objectives, planning and report
EN 16123:2013 Characterization of waste - Guidance on selection and application of screening methods
DIN EN 13369:2013-08 COMMON RULES FOR PRECAST CONCRETE PRODUCTS
I.S. EN 13369:2013 COMMON RULES FOR PRECAST CONCRETE PRODUCTS
UNI CEN/TS 15862 : 2012 CHARACTERISATION OF WASTE - COMPLIANCE LEACHING TEST - ONE STAGE BATCH LEACHING TEST FOR MONOLITHS AT FIXED LIQUID TO SURFACE AREA RATIO (L/A) FOR TEST PORTIONS WITH FIXED MINIMUM DIMENSIONS
DIN EN 14405:2017-05 CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - UP-FLOW PERCOLATION TEST (UNDER SPECIFIED CONDITIONS)
PD CEN/TS 15864:2012 Characterisation of waste. Leaching behaviour test for basic characterisation. Dynamic monolithic leaching test with continuous leachant renewal under conditions relevant for specified scenario(s)
PD CEN/TS 16637-3:2016 Construction products. Assessment of release of dangerous substances Horizontal up-flow percolation test
I.S. EN 15863:2015 CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST FOR BASIC CHARACTERIZATION - DYNAMIC MONOLITHIC LEACHING TEST WITH PERIODIC LEACHANT RENEWAL, UNDER FIXED CONDITIONS
PREN 13369 : DRAFT 2017 COMMON RULES FOR PRECAST CONCRETE PRODUCTS
I.S. EN 14405:2017 CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - UP-FLOW PERCOLATION TEST (UNDER SPECIFIED CONDITIONS)
DIN EN 14997 E : 2015 CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH CONTINUOUS PH CONTROL
PD CEN/TS 16637-2:2014 Construction products. Assessment of release of dangerous substances Horizontal dynamic surface leaching test
DIN EN 14429:2015-05 CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH INITIAL ACID/BASE ADDITION
12/30263896 DC : 0 BS EN 16457 - CHARACTERIZATION OF WASTE - FRAMEWORK FOR THE PREPARATION AND APPLICATION OF A TESTING PROGRAMME - OBJECTIVES, PLANNING AND REPORT
DIN EN 16457:2014-07 CHARACTERIZATION OF WASTE - FRAMEWORK FOR THE PREPARATION AND APPLICATION OF A TESTING PROGRAMME - OBJECTIVES, PLANNING AND REPORT
S.R. CEN/TS 16637-2:2014 CONSTRUCTION PRODUCTS - ASSESSMENT OF RELEASE OF DANGEROUS SUBSTANCES - PART 2: HORIZONTAL DYNAMIC SURFACE LEACHING TEST
S.R. CEN/TS 16637-3:2016 CONSTRUCTION PRODUCTS - ASSESSMENT OF RELEASE OF DANGEROUS SUBSTANCES - PART 3: HORIZONTAL UP-FLOW PERCOLATION TEST
I.S. EN 14429:2015 CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH INITIAL ACID/BASE ADDITION
S.R. CEN/TS 15864:2015 CHARACTERISATION OF WASTE - LEACHING BEHAVIOUR TEST FOR BASIC CHARACTERIZATION - DYNAMIC MONOLITHIC LEACHING TEST WITH CONTINUOUS LEACHANT RENEWAL UNDER CONDITIONS RELEVANT FOR SPECIFIED SCENARIO(S)
PD CEN/TS 15862:2012 Characterisation of waste. Compliance leaching test. One stage batch leaching test for monoliths at fixed liquid to surface area ratio (L/A) for test portions with fixed minimum dimensions
PD CEN/TS 15863:2012 Characterisation of waste. Leaching behaviour test for basic characterisation. Dynamic monolithic leaching test with periodic leachant renewal, under fixed test conditions
13/30291099 DC : 0 BS EN 15002 - CHARACTERIZATION OF WASTE - PREPARATION OF TEST PORTIONS FROM THE LABORATORY SAMPLE
BS EN 15863:2015 Characterization of waste. Leaching behaviour test for basic characterization. Dynamic monolithic leaching test with periodic leachant renewal, under fixed conditions
DIN EN 15002:2015-07 CHARACTERIZATION OF WASTE - PREPARATION OF TEST PORTIONS FROM THE LABORATORY SAMPLE
EN 15002:2015 Characterization of waste - Preparation of test portions from the laboratory sample
EN 16457:2014 Characterization of waste - Framework for the preparation and application of a testing programme - Objectives, planning and report
BS EN 14997:2015 Characterization of waste. Leaching behaviour test. Influence of pH on leaching with continuous pH control
13/30286649 DC : 0 BS EN 14429 - CHARACTERISATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH INITIAL ACID/BASE ADDITION
BS EN 14429:2015 Characterization of waste. Leaching behaviour test. Influence of pH on leaching with initial acid/base addition
DIN EN 16457 E : 2014 CHARACTERIZATION OF WASTE - FRAMEWORK FOR THE PREPARATION AND APPLICATION OF A TESTING PROGRAMME - OBJECTIVES, PLANNING AND REPORT
13/30286652 DC : 0 BS EN 14997 - CHARACTERISATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH CONTINUOUS PH CONTROL
BS EN 16457:2014 Characterization of waste. Framework for the preparation and application of a testing programme. Objectives, planning and report
UNE-EN 13369:2013 Common rules for precast concrete products
I.S. EN IEC 62561-7:2018 LIGHTNING PROTECTION SYSTEM COMPONENTS (LPSC) - PART 7: REQUIREMENTS FOR EARTHING ENHANCING COMPOUNDS
I.S. EN 13369:2018 COMMON RULES FOR PRECAST CONCRETE PRODUCTS
I.S. EN 14997:2015 CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH CONTINUOUS PH CONTROL
UNI CEN/TS 16637-2 : 2014 CONSTRUCTION PRODUCTS - ASSESSMENT OF RELEASE OF DANGEROUS SUBSTANCES - PART 2: HORIZONTAL DYNAMIC SURFACE LEACHING TEST
EN 13369:2018 Common rules for precast concrete products
DIN EN 15002 E : 2015 CHARACTERIZATION OF WASTE - PREPARATION OF TEST PORTIONS FROM THE LABORATORY SAMPLE
13/30286655 DC : 0 BS EN 15863 - CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST FOR BASIC CHARACTERIZATION - DYNAMIC MONOLITHIC LEACHING TEST WITH PERIODIC LEACHANT RENEWAL, UNDER FIXED TEST CONDITIONS
BS EN 15002:2015 Characterization of waste. Preparation of test portions from the laboratory sample
CEN/TS 15864:2015 Characterization of waste - Leaching behaviour test for basic characterization - Dynamic monolithic leaching test with continuous leachant renewal under conditions relevant for specified scenario(s)
EN 14429:2015 Characterization of waste - Leaching behaviour test - Influence of pH on leaching with initial acid/base addition
CEN/TS 15863:2012 Characterisation of waste - Leaching behaviour test for basic characterisation - Dynamic monolithic leaching test with periodic leachant renewal, under fixed test conditions

ISO 23913:2006 Water quality — Determination of chromium(VI) — Method using flow analysis (FIA and CFA) and spectrometric detection
ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
ISO 5725-1:1994 Accuracy (trueness and precision) of measurement methods and results — Part 1: General principles and definitions
EN ISO 17294-1:2006 Water quality - Application of inductively coupled plasma mass spectrometry (ICP-MS) - Part 1: General guidelines (ISO 17294-1:2004)
EN ISO 14403 : 2002 WATER QUALITY - DETERMINATION OF TOTAL CYANIDE AND FREE CYANIDE BY CONTINUOUS FLOW ANALYSIS
ISO 14402:1999 Water quality Determination of phenol index by flow analysis (FIA and CFA)
EN 12457-2:2002 Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 2: One stage batch test at a liquid to solid ratio of 10 l/kg for materials with particle size below 4 mm (without or with size reduction)
EN 1483:2007 Water quality - Determination of mercury - Method using atomic absorption spectrometry
CEN/TS 14429:2005 Characterization of waste - Leaching behaviour tests - Influence of pH on leaching with initial acid/base addition
EN ISO 11885:2009 Water quality - Determination of selected elements by inductively coupled plasma optical emission spectrometry (ICP-OES) (ISO 11885:2007)
EN 27888 : 1993 WATER QUALITY - DETERMINATION OF ELECTRICAL CONDUCTIVITY
ISO 11969:1996 Water quality Determination of arsenic Atomic absorption spectrometric method (hydride technique)
ISO 11083:1994 Water quality — Determination of chromium(VI) — Spectrometric method using 1,5-diphenylcarbazide
EN ISO 10304-3 : 1997 Water quality - Determination of dissolved anions by liquid chromatography of ions - Part 3: Determination of chromate, iodide, sulfite, thiocyanate and thiosulfate (ISO 10304-3:1997)
EN ISO 11732:2005 Water quality - Determination of ammonium nitrogen - Method by flow analysis (CFA and FIA) and spectrometric detection (ISO 11732:2005)
EN ISO 15586 : 2003 WATER QUALITY - DETERMINATION OF TRACE ELEMENTS USING ATOMIC ABSORPTION SPECTROMETRY WITH GRAPHITE FURNACE
ISO/TR 13530:1997 Water quality Guide to analytical quality control for water analysis
EN 26777 : 1993 WATER QUALITY - DETERMINATION OF NITRITE - MOLECULAR ABSORPTION SPECTROMETRIC METHOD
EN 1484 : 1997 WATER ANALYSIS - GUIDELINES FOR THE DETERMINATION OF TOTAL ORGANIC CARBON (TOC) AND DISSOLVED ORGANIC CARBON (DOC)
ISO 10304-3:1997 Water quality — Determination of dissolved anions by liquid chromatography of ions — Part 3: Determination of chromate, iodide, sulfite, thiocyanate and thiosulfate
ISO 11732:2005 Water quality — Determination of ammonium nitrogen — Method by flow analysis (CFA and FIA) and spectrometric detection
ISO 15682:2000 Water quality Determination of chloride by flow analysis (CFA and FIA) and photometric or potentiometric detection
ISO 17852:2006 Water quality Determination of mercury Method using atomic fluorescence spectrometry
ISO 5725-3:1994 Accuracy (trueness and precision) of measurement methods and results — Part 3: Intermediate measures of the precision of a standard measurement method
CEN/TS 14997 : 2006 CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TESTS - INFLUENCE OF PH ON LEACHING WITH CONTINUOUS PH-CONTROL
ISO 9965:1993 Water quality Determination of selenium Atomic absorption spectrometric method (hydride technique)
ISO 5725-6:1994 Accuracy (trueness and precision) of measurement methods and results — Part 6: Use in practice of accuracy values
EN 12457-4:2002 Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 4: One stage batch test at a liquid to solid ratio of 10 l/kg for materials with particle size below 10 mm (without or with size reduction)
ISO 8288:1986 Water quality — Determination of cobalt, nickel, copper, zinc, cadmium and lead — Flame atomic absorption spectrometric methods
ISO 5725-4:1994 Accuracy (trueness and precision) of measurement methods and results Part 4: Basic methods for the determination of the trueness of a standard measurement method
ISO 9297:1989 Water quality Determination of chloride Silver nitrate titration with chromate indicator (Mohr's method)
EN ISO 17852:2008 Water quality - Determination of mercury - Method using atomic fluorescence spectrometry (ISO 17852:2006)
EN ISO 23913:2009 Water quality - Determination of chromium(VI) - Method using flow analysis (FIA and CFA) and spectrometric detection (ISO 23913:2006)
ISO 11885:2007 Water quality Determination of selected elements by inductively coupled plasma optical emission spectrometry (ICP-OES)
ISO 17294-1:2004 Water quality Application of inductively coupled plasma mass spectrometry (ICP-MS) Part 1: General guidelines
ISO 10304-1:2007 Water quality Determination of dissolved anions by liquid chromatography of ions Part 1: Determination of bromide, chloride, fluoride, nitrate, nitrite, phosphate and sulfate
ISO 6703-2:1984 Water quality — Determination of cyanide — Part 2: Determination of easily liberatable cyanide
ISO 6439:1990 Water quality — Determination of phenol index — 4-Aminoantipyrine spectrometric methods after distillation
ISO 13395:1996 Water quality — Determination of nitrite nitrogen and nitrate nitrogen and the sum of both by flow analysis (CFA and FIA) and spectrometric detection
ISO 10359-1:1992 Water quality — Determination of fluoride — Part 1: Electrochemical probe method for potable and lightly polluted water
CEN/TR 16184:2011 Characterization of Waste - State-of-the-art document - Analysis of eluates
ENV ISO 13530 : DRAFT 1998 WATER QUALITY - GUIDE TO ANALYTICAL QUALITY CONTROL FOR WATER ANALYSIS
ISO 15586:2003 Water quality Determination of trace elements using atomic absorption spectrometry with graphite furnace
NEN 6604 : 2007 WATER QUALITY - DETERMINATION OF AMMONIUM, NITRATE, NITRITE, CHLORIDE, ORTHO-PHOSPHATE, SULPHATE AND SILICATE BY A DISCRETE ANALYZER SYSTEM AND SPECTROPHOTOMETRIC DETECTION
ISO 7888:1985 Water quality — Determination of electrical conductivity
EN 12457-1:2002 Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 1: One stage batch test at a liquid to solid ratio of 2 l/kg for materials with high solid content and with particle size below 4 mm (without or with size reduction)
ISO 5725-2:1994 Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method
ISO 14403:2002 Water quality Determination of total cyanide and free cyanide by continuous flow analysis
ISO 9562:2004 Water quality — Determination of adsorbable organically bound halogens (AOX)
ISO 22743:2006 Water quality Determination of sulfates Method by continuous flow analysis (CFA)
EN 12920:2006+A1:2008 Characterization of waste - Methodology for the determination of the leaching behaviour of waste under specified conditions
EN 15002:2015 Characterization of waste - Preparation of test portions from the laboratory sample
EN ISO 15682 : 2001 WATER QUALITY - DETERMINATION OF CHLORIDE BY FLOW ANALYSIS (CFA AND FIA) AND PHOTOMETRIC OR POTENTIOMETRIC DETECTION
EN 12457-3:2002 Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 3: Two stage batch test at a liquid to solid ratio of 2 l/kg and 8 l/kg for materials with high solid content and with particle size below 4 mm (without or with size reduction)
EN 12506:2003 Characterization of waste - Analysis of eluates - Determination of pH, As, Ba, Cd, Cl-, Co, Cr, Cr Vl, Cu, Mo, Ni, NO2-, Pb, total S, SO42-, V and Zn
EN ISO 9562:2004 Water quality - Determination of adsorbable organically bound halogens (AOX) (ISO 9562:2004)
ISO 7150-1:1984 Water quality — Determination of ammonium — Part 1: Manual spectrometric method
CEN/TS 14405 : 2004 CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TESTS - UP-FLOW PERCOLATION TEST (UNDER SPECIFIED CONDITIONS)
ISO 10523:2008 Water quality — Determination of pH
EN 15216:2007 Characterization of waste - Determination of total dissolved solids (TDS) in water and eluates
EN ISO 11969:1996 WATER QUALITY - DETERMINATION OF ARSENIC - ATOMIC ABSORPTION SPECTROMETRIC METHOD (HYDRIDE TECHNIQUE)
ISO 5725-5:1998 Accuracy (trueness and precision) of measurement methods and results — Part 5: Alternative methods for the determination of the precision of a standard measurement method
EN ISO 14402 : 1999 WATER QUALITY - DETERMINATION OF PHENOL INDEX BY FLOW ANALYSIS (FIA AND CFA)
EN ISO 10304-1:2009 Water quality - Determination of dissolved anions by liquid chromatography of ions - Part 1: Determination of bromide, chloride, fluoride, nitrate, nitrite, phosphate and sulfate (ISO 10304-1:2007)
ISO 17294-2:2016 Water quality — Application of inductively coupled plasma mass spectrometry (ICP-MS) — Part 2: Determination of selected elements including uranium isotopes
EN ISO 14911 : 1999 WATER QUALITY - DETERMINATION OF DISSOLVED LI+, NA+, NH4+, K+, MN2+, CA2+, MG2+, SR2+ AND BA2+ USING ION CHROMATOGRAPHY - METHOD FOR WATER AND WASTE WATER
EN ISO 17294-2:2016 Water quality - Application of inductively coupled plasma mass spectrometry (ICP-MS) - Part 2: Determination of selected elements including uranium isotopes (ISO 17294-2:2016)
ISO 14911:1998 Water quality Determination of dissolved Li+, Na+, NH4+, K+, Mn2+, Ca2+, Mg2+, Sr2+ and Ba2+ using ion chromatography Method for water and waste water
EN ISO 13395 : 1996 WATER QUALITY - DETERMINATION OF NITRITE NITROGEN AND NITRATE NITROGEN AND THE SUM OF BOTH BY FLOW ANALYSIS (CFA AND FIA) AND SPECTROMETRIC DETECTION

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.