• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 476:2011

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

General requirements for components used in drains and sewers

Superseded date

05-05-2022

Published date

12-01-2011

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 Dimensional requirements
6 Performance requirements
7 Test methods
8 Marking, labelling and packaging
Bibliography

This European Standard specifies general requirements for components inside and outside buildings (see EN 12056-1) such as pipes, fittings and manholes with their respective joints intended for use in discharge pipes, drains and sewers which operate as gravity systems allowing for a maximum pressure of 40 kPa.It also specifies general requirements for components used in hydraulically and pneumatically pressurised discharge pipes, drains and sewers. It provides basic specifications to be respected in material related product standards for these applications.It is not applicable for the direct evaluation of products. It is applicable as a reference for drawing up a product specification, if there is no product standard available. NOTEWhere the term "inside buildings" is used in the context of components fixed inside buildings, it also includes discharge pipes and fittings fixed on external surfaces of buildings.This European Standard covers components to be used in conveying in a satisfactory manner:-domestic wastewater;-rainwater and surface water; and-other waste waters acceptable for discharge into the system (e.g. industrial wastewater).This European standard applies to components of circular and other cross sections.This European Standard applies equally to components which are factory-made and to those constructed on site, where applicable.This European Standard does not apply to components used for trenchless construction according to EN 14457 and for components used for renovation of drains and sewers according to EN 13380.

Committee
CEN/TC 165
DevelopmentNote
Supersedes EN 1293 & EN 773. (01/2011)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
NEN EN 476 : 2011 Identical
I.S. EN 476:2011 Identical
BS EN 476:2011 Identical
NF EN 476 : 2011 Identical
SN EN 476 : 2011 Identical
UNE-EN 476:2011 Identical
DIN EN 476:2011-04 Identical
PN EN 476 : 2012 Identical
UNI EN 476 : 2011 Identical
NS EN 476 : 2011 Identical
NBN EN 476 : 2011 Identical
ONORM EN 476 : 2011 Identical

16/30329419 DC : 0 BS EN 12566-1 - SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 1: PREFABRICATED SEPTIC TANKS
PREN 1451-1 : DRAFT 2016 PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
12/30254917 DC : DRAFT JAN 2012 BS EN 877 - CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE
PREN 1519-1 : DRAFT 2017 PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - POLYETHYLENE (PE) - PART 1: REQUIREMENTS FOR PIPES, FITTINGS AND THE SYSTEM
16/30336859 DC : 0 BS EN 1852-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
16/30329416 DC : 0 BS EN 12566-3 - SMALL WASTEWATER TREATMENT SYSTEMS UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS
DIN EN 15383:2014-02 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS
16/30332879 DC : 0 BS EN 1451-1 - PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
14/30310792 DC : 0 BS EN 13598-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS IN TRAFFIC AREAS AND DEEP UNDERGROUND INSTALLATIONS
BS EN 16323:2014 Glossary of wastewater engineering terms
ISO 7682:2003 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Acrylonitrile-butadiene-styrene (ABS)
06/30148351 DC : 0 EN 12566-6 - SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 6: PREFABRICATED TREATMENT UNITS FOR SEPTIC TANK EFFLUENT
09/30198143 DC : 0 BS ISO 13268 - THERMOPLASTICS PIPING SYSTEMS FOR NON PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - THERMOPLASTICS SHAFTS OR RISERS FOR INSPECTION CHAMBERS AND MANHOLES - DETERMINATION OF RING STIFFNESS
UNE-EN 13598-2:2017 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for manholes and inspection chambers
PREN 1401-1 : DRAFT 2018 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEMS
S.R. CEN/TS 15223:2017 PLASTICS PIPING SYSTEMS - VALIDATED DESIGN PARAMETERS OF BURIED THERMOPLASTICS PIPING SYSTEMS
ISO 19220:2004 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Styrene copolymer blends (SAN + PVC)
I.S. EN 12566-7:2016 SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 7: PREFABRICATED TERTIARY TREATMENT UNITS
UNE-EN 16397-2:2015 Flexible couplings - Part 2: Characteristics and testing for metal banded flexible couplings, adaptors and bushes
I.S. EN 1852-1:2018 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
BS EN 12566-6:2013 Small wastewater treatment systems for up to 50 PT Prefabricated treatment units for septic tank effluent
UNI EN 15383 : 2013-11 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS
I.S. EN 12566-3:2016 SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS
BS EN 13476-3 : 2007 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B
DIN EN 1253-1:2015-03 GULLIES FOR BUILDINGS - PART 1: TRAPPED FLOOR GULLIES WITH A DEPTH WATER SEAL OF AT LEAST 50 MM
DIN EN 14364 E : 2013 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS
BS EN 1566-1:2000 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Chlorinated poly(vinyl chloride) (PVC-C) Specification for pipes, fittings and the system
UNE-EN 12200-1:2017 Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
BS EN 274-1:2002 Waste fittings for sanitary appliances Requirements
DIN EN 14982:2011-01 Plastics piping and ducting systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness (includes Amendment A1:2010)
BS EN 12255-10:2001 Wastewater treatment plants Safety principles
BS EN 877 : 1999 CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE
BS EN 13564-1:2002 Anti-flooding devices for buildings Requirements
UNE-CEN/TR 1295-3:2011 IN Structural design of buried pipelines under various conditions of loading - Part 3: Common method
BS EN 1253-2:2015 Gullies for buildings Roof drains and floor gullies without trap
I.S. EN 877:2000 CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE
CEN/TR 12566-2:2005 Small wastewater treatment systems for up to 50 PT - Part 2: Soil infiltration systems
EN 1123-3:2004 Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Part 3: Dimensions and special requirements for vacuum drainage systems and for drainage systems in ship-building
EN 12566-6:2016 Small wastewater treatment systems for up to 50 PT - Part 6: Prefabricated treatment units for septic tank effluent
EN 16932-3:2018 Drain and sewer systems outside buildings - Pumping systems - Part 3: Vacuum systems
EN 13508-2:2003+A1:2011 Investigation and assessment of drain and sewer systems outside buildings - Part 2: Visual inspection coding system
EN 12566-7:2016 Small wastewater treatment systems for up to 50 PT - Part 7: Prefabricated tertiary treatment units
EN 1124-1:1999/A1:2004 PIPES AND FITTINGS OF LONGITUDINALLY WELDED STAINLESS STEEL PIPES WITH SPIGOT AND SOCKET FOR WASTE WATER SYSTEMS - PART 1: REQUIREMENTS, TESTING, QUALITY CONTROL
EN 12566-3:2016 Small wastewater treatment systems for up to 50 PT - Part 3: Packaged and/or site assembled domestic wastewater treatment plants
CEN/TR 1295-3:2007 Structural design of buried pipelines under various conditions of loading - Part 3: Common method
EN 12255-10:2000 Wastewater treatment plants - Part 10: Safety principles
UNI EN 877 : 2007 CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE
DIN EN 14830:2007-01 Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance
EN 1123-1:1999/A1:2004 PIPES AND FITTINGS OF LONGITUDINALLY WELDED HOT-DIP GALVANIZED STEEL PIPES WITH SPIGOT AND SOCKET FOR WASTE WATER SYSTEMS - PART 1: REQUIREMENTS, TESTING, QUALITY CONTROL
EN 12666-1:2005+A1:2011 Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system
DIN EN 13476-2:2007-08 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A
EN 877:1999/A1:2006/AC:2008 CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE
EN 12763:2000 Fibre-cement pipes and fittings for discharge systems for buildings - Dimensions and technical terms of delivery
EN 1253-2:2015 GULLIES FOR BUILDINGS - PART 2: ROOF DRAINS AND FLOOR GULLIES WITHOUT TRAP
EN 12566-1:2016 Small wastewater treatment systems for up to 50 PT - Part 1: Prefabricated septic tanks
I.S. EN 14830:2006 THERMOPLASTICS INSPECTION CHAMBER AND MANHOLE BASES - TEST METHODS FOR BUCKLING RESISTANCE
I.S. EN 12255-10:2000 WASTEWATER TREATMENT PLANTS - PART 10: SAFETY PRINCIPLES
I.S. EN 14802:2006 PLASTICS PIPING SYSTEMS - THERMOPLASTICS SHAFTS OR RISERS FOR INSPECTION CHAMBERS AND MANHOLES - DETERMINATION OF RESISTANCE AGAINST SURFACE AND TRAFFIC LOADING
I.S. CEN/TR 12566-2:2005 SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 2: SOIL INFILTRATION SYSTEMS
PREN 14364 : DRAFT 2011 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS
02/103343 DC : DRAFT MAY 2002 PREN 14457 - GENERAL REQUIREMENTS FOR COMPONENTS SPECIFICALLY DESIGNED FOR USE IN TRENCHLESS CONSTRUCTION OF DRAINS AND SEWERS
06/30151317 DC : 0 BS EN 1124-2 - PIPES AND FITTINGS OF LONGITUDINALLY WELDED STAINLESS STEEL PIPES WITH SPIGOT AND SOCKET FOR WASTE WATER SYSTEMS - PART 2: SYSTEMS - DIMENSIONS
15/30327642 DC : 0 BS EN 13476-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS
05/30131069 DC : DRAFT MAR 2005 EN 598:2005 - DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS
UNE-EN 14636-1:2010 Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints
11/30246452 DC : 0 BS EN 14758-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE WITH MINERAL MODIFIERS (PP-MD) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
13/30260531 DC : 0 BS EN 1253-2 - GULLIES FOR BUILDINGS - PART 2: ROOF DRAINS AND FLOOR GULLIES WITHOUT TRAP
13/30295203 DC : 0 BS EN 1610 - CONSTRUCTION AND TESTING OF DRAINS AND SEWERS
17/30364341 DC : 0 BS EN 1519-1 - PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - POLYETHYLENE (PE) - PART 1: REQUIREMENTS FOR PIPES, FITTINGS AND THE SYSTEM
BS EN 16397-2:2014 Flexible couplings Characteristics and testing for metal banded flexible couplings, adaptors and bushes
PREN 12566-1 : DRAFT 2015 SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 1: PREFABRICATED SEPTIC TANKS
10/30237537 DC : 0 EN 15383 - PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS
05/30132762 DC : 0 PREN 15229 - PLASTICS PIPING SYSTEMS - PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - PERFORMANCE REQUIREMENTS FOR THERMOPLASTICS MANHOLES AND INSPECTION CHAMBERS
11/30246455 DC : 0 BS EN 1796 - PLASTICS PIPING SYSTEMS FOR WATER SUPPLY WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP)
UNI EN 14364 : 2013 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS
PREN 1253-2 : DRAFT 2013 GULLIES FOR BUILDINGS - PART 2: ROOF DRAINS AND FLOOR GULLIES WITHOUT TRAP
07/30165577 DC : 0 BS EN 1852-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
12/30258203 DC : 0 BS EN 16397-1 - FLEXIBLE COUPLINGS - PART 1: PERFORMANCE REQUIREMENTS
I.S. EN 16932-1:2018 DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - PUMPING SYSTEMS - PART 1: GENERAL REQUIREMENTS
PREN 13476-2 : DRAFT 2015 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A
ISO 7675:2003 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Chlorinated poly(vinyl chloride) (PVC-C)
UNE-EN 16397-1:2015 Flexible couplings - Part 1: Performance requirements
I.S. EN 16397-2:2014 FLEXIBLE COUPLINGS - PART 2: CHARACTERISTICS AND TESTING FOR METAL BANDED FLEXIBLE COUPLINGS, ADAPTORS AND BUSHES
UNI EN 1796 : 2013 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP)
I.S. EN 16323:2014 GLOSSARY OF WASTEWATER ENGINEERING TERMS
I.S. EN 13476-3:2007 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY (VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B
PREN 1852-1 : DRAFT 2016 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
PREN 752 : DRAFT 2015 DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - SEWER SYSTEM MANAGEMENT
18/30371677 DC : DRAFT MAY 2018 BS EN 1401-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEMS
EN 1566-1:1998 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system
EN 1565-1:1998 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 1: Specifications for pipes, fittings and the system
EN 1852-1:2018 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
DIN EN 877:2010-01 Cast iron pipes and fittings, their joints and accessories for the evacuation of water from buildings - Requirements, test methods and quality assurance (includes Amendment A1:2006 and Corrigendum AC:2008)
DIN EN 14758-1:2012-05 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
NF EN 13598-1 : 2011 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS
DIN EN 1123-3:2005-02 Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Part 3: Dimensions and special requirements for vacuum drainage systems and for drainage systems in shipbuilding
DIN EN 598:2009-10 Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods (includes Amendment A1:2009)
DIN EN 14802 E : 2006 PLASTICS PIPING SYSTEMS - THERMOPLASTICS SHAFTS OR RISERS FOR INSPECTION CHAMBERS AND MANHOLES - DETERMINATION OF RESISTANCE AGAINST SURFACE AND TRAFFIC LOADING
DIN EN 14364:2013-05 Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
BS EN 598 : 2007 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS
BS EN 14982 : 2006 PLASTICS PIPING AND DUCTING SYSTEMS - THERMOPLASTICS SHAFTS OR RISERS FOR INSPECTION CHAMBERS AND MANHOLES - DETERMINATION OF RING STIFFNESS
BS EN 13380:2001 General requirements for components used for renovation and repair of drain and sewer systems outside buildings
BS EN 14802:2005 Plastics piping systems. Thermoplastics shafts or risers for inspection chambers and manholes. Determination of resistance against surface and traffic loading
DIN EN 752:2015-10 (Draft) DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - SEWER SYSTEM MANAGEMENT
I.S. EN 13508-2:2003 INVESTIGATION AND ASSESSMENT OF DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - PART 2: VISUAL INSPECTION CODING SYSTEM
I.S. EN 1253-2:2015 GULLIES FOR BUILDINGS - PART 2: ROOF DRAINS AND FLOOR GULLIES WITHOUT TRAP
I.S. EN 598:2007 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS
DIN EN 1796:2013-05 Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)
I.S. EN 1253-1:2015 GULLIES FOR BUILDINGS - PART 1: TRAPPED FLOOR GULLIES WITH A DEPTH WATER SEAL OF AT LEAST 50 MM
I.S. EN 12200-1:2016 PLASTICS RAINWATER PIPING SYSTEMS FOR ABOVE GROUND EXTERNAL USE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
I.S. EN 1610:2015 CONSTRUCTION AND TESTING OF DRAINS AND SEWERS
I.S. EN 12566-1:2016 SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 1: PREFABRICATED SEPTIC TANKS
I.S. EN 1796:2013 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP)
I.S. EN 14758-1:2012 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE WITH MINERAL MODIFIERS (PP-MD) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
I.S. EN 14364:2013 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS
I.S. EN 1253-4:2016 GULLIES FOR BUILDINGS - PART 4: ACCESS COVERS
DIN EN 858-1:2002-05 CONTINUOUS HANDLING EQUIPMENT AND SYSTEMS - PART 1: SAFETY AND EMC REQUIREMENTS FOR THE EQUIPMENT FOR THE STORAGE OF BULK MATERIALS IN SILOS, BUNKERS, BINS AND HOPPERS
I.S. EN 12666-1:2006 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
S.R. CEN/TR 1295-3:2007 STRUCTURAL DESIGN OF BURIED PIPELINES UNDER VARIOUS CONDITIONS OF LOADING - PART 3: COMMON METHOD
I.S. EN 14982:2006 PLASTICS PIPING AND DUCTING SYSTEMS - THERMOPLASTICS SHAFTS OR RISERS FOR INSPECTION CHAMBERS AND MANHOLES - DETERMINATION OF RING STIFFNESS
UNI EN 14758-1 : 2012 PLASTICS PIPING SYSTEMS FOR NON- PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE WITH MINERAL MODIFIERS (PP-MD) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
I.S. EN 15383:2012 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS
09/30203912 DC : 0 BS EN 12566-7 - SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 7: PREFABRICATED TERTIARY TREATMENT UNITS
11/30250267 DC : 0 BS EN 16323 - GLOSSARY OF WASTEWATER ENGINEERING TERMS
UNI EN 14636-1 : 2010 PLASTICS PIPING SYSTEMS FOR NON- PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 1: PIPES AND FITTINGS WITH FLEXIBLE JOINTS
DIN EN 16397-1 E : 2015 FLEXIBLE COUPLINGS - PART 1: PERFORMANCE REQUIREMENTS
06/30124428 DC : 0 EN 13598-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY (VINYL CHLORIDE)(PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS IN TRAFFIC AREAS AND DEEP UNDERGROUND INSTALLATIONS
UNI EN 16397-1 : 2014 FLEXIBLE COUPLINGS - PART 1: PERFORMANCE REQUIREMENTS
CEN/TR 1046:2013 Thermoplastics piping and ducting systems - Systems outside building structures for the conveyance of water or sewage - Practices for underground installation
11/30246458 DC : 0 BS EN 14364 - PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS
BS EN 14636-2:2009 Plastics piping systems for non-pressure drainage and sewerage. Polyester resin concrete (PRC) Manholes and inspection chambers
03/102186 DC : DRAFT AUG 2003 EN 14758-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE WITH MINERAL MODIFIERS (PP-M) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
01/107111 DC : DRAFT SEP 2001 BS EN 12566-3 - SMALL WASTEWATER TREATMENT SYSTEMS UP TO 50 PT - PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS
UNI EN 16323 : 2014 GLOSSARY OF WASTEWATER ENGINEERING TERMS
EN 1796:2013 Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)
EN 1455-1:1999 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Requirements for pipes, fittings and the system
ISO 7671:2003 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Polypropylene (PP)
I.S. EN 14636-1:2009 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 1: PIPES AND FITTINGS WITH FLEXIBLE JOINTS
I.S. EN 1451-1:2017 PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
BS EN 1852-1:2018 Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene (PP) Specifications for pipes, fittings and the system
EN 1451-1:2017 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
EN 13476-3:2018 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B
DIN EN 13476-1:2015-11 (Draft) PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS
BS EN 13476-2:2007 Plastics piping systems for non-pressure underground drainage and sewerage. Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Specifications for pipes and fittings with smooth internal and external surface and the system, Type A
UNI EN 16397-2 : 2014 FLEXIBLE COUPLINGS - PART 2: CHARACTERISTICS AND TESTING FOR METAL BANDED FLEXIBLE COUPLINGS, ADAPTORS AND BUSHES
PREN 13476-3 : DRAFT 2015 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B
EN 14636-1:2009 Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints
EN 16932-1:2018 Drain and sewer systems outside buildings - Pumping systems - Part 1: General requirements
DIN EN 14982 E : 2011 PLASTICS PIPING AND DUCTING SYSTEMS - THERMOPLASTICS SHAFTS OR RISERS FOR INSPECTION CHAMBERS AND MANHOLES - DETERMINATION OF RING STIFFNESS
DIN EN 1433:2005-09 DRAINAGE CHANNELS FOR VEHICULAR AND PEDESTRIAN AREAS - CLASSIFICATION, DESIGN AND TESTING REQUIREMENTS, MARKING AND EVALUATION OF CONFORMITY
DIN EN 12666-1:2011-11 Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system (includes Amendment A1:2011)
DIN EN 14830 E : 2007 THERMOPLASTICS INSPECTION CHAMBER AND MANHOLE BASES - TEST METHODS FOR BUCKLING RESISTANCE
UNE-EN 14758-1:2012 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
BS EN 14830:2006 Thermoplastics inspection chamber and manhole bases. Test methods for buckling resistance
BS EN 588-2:2001 Fibre-cement pipes for sewers and drains Manholes and inspection chambers
BS EN 13598-1:2010 Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Specifications for ancillary fittings including shallow inspection chambers
BS EN 1401-1:2009 Plastic piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U) Specifications for pipes, fittings and the system
BS EN 1123-3:2004 Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems Dimensions and special requirements for vacuum drainage systems and for drainage systems in ship-building
UNE-EN 1610:2016 Construction and testing of drains and sewers
EN 13476-2:2018+A1:2020 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A
I.S. EN 13598-1:2010 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS
EN 16397-1:2014 Flexible couplings - Part 1: Performance requirements
UNI EN 13508-2 : 2011 INVESTIGATION AND ASSESSMENT OF DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - PART 2: VISUAL INSPECTION CODING SYSTEM
UNI EN 14982 : 2010 PLASTICS PIPING AND DUCTING SYSTEMS - THERMOPLASTICS SHAFTS OR RISERS FOR INSPECTION CHAMBERS AND MANHOLES - DETERMINATION OF RING STIFFNESS
UNI EN 12666-1 : 2011 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
UNI EN 1401-1 : 2009 PLASTICS PIPING SYSTEMS FOR NON- PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
UNI EN 598 : 2009 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS
UNI EN 13598-1 : 2011 PLASTICS PIPING SYSTEMS FOR NON- PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VILYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS
DIN EN 16397-2:2015-01 FLEXIBLE COUPLINGS - PART 2: CHARACTERISTICS AND TESTING FOR METAL BANDED FLEXIBLE COUPLINGS, ADAPTORS AND BUSHES
DIN EN 16323:2014-07 GLOSSARY OF WASTEWATER ENGINEERING TERMS
I.S. EN 752:2017 DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - SEWER SYSTEM MANAGEMENT
DIN 1986-3:2004-11 Drainage systems on private ground - Part 3: Specifications for service and maintenance
15/30317327 DC : 0 BS EN 16941-1 - ON-SITE NON-POTABLE WATER SYSTEMS - PART 1: SYSTEMS FOR THE USE OF RAINWATER
PD CEN/TR 15128:2005 Survey of European standards for rehabilitation of drain and sewer systems
BS ISO 13268:2010 Thermoplastics piping systems for non-pressure underground drainage and sewerage. Thermoplastics shafts or risers for inspection chambers and manholes. Determination of ring stiffness
DIN EN 13598-2 E : 2016 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS
DIN EN 15383 E : 2014 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS
I.S. EN 274-1:2002 WASTE FITTINGS FOR SANITARY APPLIANCES - PART 1: REQUIREMENTS
12/30258206 DC : 0 BS EN 16397-2 - FLEXIBLE COUPLINGS - PART 2: MATERIALS AND DIMENSIONS FOR METAL BANDED FLEXIBLE COUPLINGS
13/30260528 DC : 0 BS EN 1253-1 - GULLIES FOR BUILDINGS - PART 1: TRAPPED FLOOR GULLIES WITH A DEPTH WATER SEAL OF AT LEAST 50 MM
09/30203307 DC : DRAFT JULY 2009 BS EN 14636-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS
BS EN 16932-3:2018 Drain and sewer systems outside buildings. Pumping systems Vacuum systems
BS EN 14636-1:2009 Plastics piping systems for non-pressure drainage and sewerage. Polyester resin concrete (PRC) Pipes and fittings with flexible joints
PREN 14636-2 : DRAFT 2009 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS
PREN 13598-2 : DRAFT 2014 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS IN TRAFFIC AREAS AND DEEP UNDERGROUND INSTALLATIONS
UNE-EN 12566-6:2017 Small wastewater treatment systems for up to 50 PT - Part 6: Prefabricated treatment units for septic tank effluent
PREN 1610 : DRAFT 2013 CONSTRUCTION AND TESTING OF DRAINS AND SEWERS
98/106709 DC : DRAFT AUG 98 PREN 12566-3 - SMALL WASTE-WATER TREATMENT SYSTEMS UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTE-WATER TREATMENT PLANTS
BS EN 15383 : 2012 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS
BS EN 16397-1:2014 Flexible couplings Performance requirements
02/121757 DC : DRAFT APR 2002 BS ISO 19220 - PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) INSIDE BUILDINGS - STYRENE COPOLYMER BLENDS (SAN + PVC)
S.R. CEN/TR 1046:2013 THERMOPLASTICS PIPING AND DUCTING SYSTEMS - SYSTEMS OUTSIDE BUILDING STRUCTURES FOR THE CONVEYANCE OF WATER OR SEWAGE - PRACTICES FOR UNDERGROUND INSTALLATION
I.S. EN 14636-2:2009 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS
I.S. EN 16397-1:2014 FLEXIBLE COUPLINGS - PART 1: PERFORMANCE REQUIREMENTS
ISO 8770:2003 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Polyethylene (PE)
BS EN 13476-1:2007 Plastics piping systems for non-pressure underground drainage and sewerage. Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) General requirements and performance characteristics
ISO 13268:2010 Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics shafts or risers for inspection chambers and manholes Determination of ring stiffness
PREN 1253-1 : DRAFT 2013 GULLIES FOR BUILDINGS - PART 1: TRAPPED FLOOR GULLIES WITH A DEPTH WATER SEAL OF AT LEAST 50 MM
BS EN 12566-7:2013 Small wastewater treatment systems for up to 50 PT Prefabricated tertiary treatment units
PREN 13476-1 : DRAFT 2015 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYLSEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS
CEN/TS 15223:2017 Plastics piping systems - Validated design parameters of buried thermoplastics piping systems
PREN 14758-1 : DRAFT 2011 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE WITH MINERAL MODIFIERS (PP-MD) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
UNE-EN 12566-7:2017 Small wastewater treatment systems for up to 50 PT - Part 7: Prefabricated tertiary treatment units
ISO 13272:2011 Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifiers (PP-MD) and polyethylene (PE) — Specifications for manholes and inspection chambers in traffic areas and underground installations
EN 13476-1:2018 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1:General requirements and performance characteristics
I.S. EN 1455-1:1999 PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) - PART 1: REQUIREMENTS FOR PIPES, FITTINGS AND THE SYSTEM
DIN EN 13476-2:2015-11 (Draft) PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A
DIN EN 14457 E : 2004 GENERAL REQUIREMENTS FOR COMPONENTS SPECIFICALLY DESIGNED FOR USE IN TRENCHLESS CONSTRUCTION OF DRAINS AND SEWERS
UNE-EN 1796:2014 Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)
BS EN 1124-1:1999 Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems Requirements, testing, quality control
BS EN 12763:2000 Fibre-cement pipes and fittings for discharge systems for buildings. Dimensions and technical terms of delivery
UNE-EN 1253-4:2017 Gullies for buildings - Part 4: Access covers
UNE-EN 12566-3:2017 Small wastewater treatment systems for up to 50 PT - Part 3: Packaged and/or site assembled domestic wastewater treatment plants
BS EN 1455-1:2000 Plastics piping systems for soil and waste (low and high temperature) within the building structure. Acrylonitrile-butadiene-styrene (ABS) Specifications for pipes, fittings and the system
EN 13598-2:2016 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for manholes and inspection chambers
BS EN 12566-3 : 2005 SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS
DIN EN 13598-1:2011-02 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS
UNE-EN 13598-1:2011 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings including shallow inspection chambers
BS EN 12200-1:2016 Plastics rainwater piping systems for above ground external use. Unplasticized poly(vinyl chloride) (PVC-U) Specifications for pipes, fittings and the system
BS EN 1796:2013 Plastics piping systems for water supply with or without pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)
UNE-EN 12566-1:2017 Small wastewater treatment systems for up to 50 PT - Part 1: Prefabricated septic tanks
BS EN 1253-1:2015 Gullies for buildings Trapped floor gullies with a depth water seal of at least 50 mm
BS EN 12666-1 : 2005 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
BS EN 1610:2015 Construction and testing of drains and sewers
UNE EN 15383 : 0 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS
EN 13598-1:2010 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings including shallow inspection chambers
BS EN 14758-1:2012 Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene with mineral modifiers (PP-MD) Specifications for pipes, fittings and the system
UNE-EN 14364:2015 Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
BS EN 13508-2 : 2003 INVESTIGATION AND ASSESSMENT OF DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - PART 2: VISUAL INSPECTION CODING SYSTEM
BS EN 14364:2013 Plastics piping systems for drainage and sewerage with or without pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Specifications for pipes, fittings and joints
BS EN 1123-1:1999 Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems Requirements, testing, quality control
EN 274-1:2002 Waste fittings for sanitary appliances - Part 1: Requirements
EN 858-1:2002/A1:2004 SEPARATOR SYSTEMS FOR LIGHT LIQUIDS (E.G. OIL AND PETROL) - PART 1: PRINCIPLES OF PRODUCT DESIGN, PERFORMANCE AND TESTING, MARKING AND QUALITY CONTROL
EN 588-2:2001 Fibre cement pipes for drains and sewers - Part 2: Manholes and inspection chambers
BS EN 1433:2002 Drainage channels for vehicular and pedestrian areas. Classification, design and testing requirements, marking and evaluation of conformity
EN 1433:2002/A1:2005 DRAINAGE CHANNELS FOR VEHICULAR AND PEDESTRIAN AREAS - CLASSIFICATION, DESIGN AND TESTING REQUIREMENTS, MARKING AND EVALUATION OF CONFORMITY
EN 15383:2012+A1:2013 Plastics piping systems for drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Manholes and inspection chambers
ONORM EN 877 : 2008 CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE
EN 1401-1:2009 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
EN 1610:2015 Construction and testing of drains and sewers
EN 752:2017 Drain and sewer systems outside buildings - Sewer system management
EN 16397-2:2014 Flexible couplings - Part 2: Characteristics and testing for metal banded flexible couplings, adaptors and bushes
EN 14457:2004 General requirements for components specifically designed for use in trenchless construction of drains and sewers
EN 14982:2006+A1:2010 Plastics piping and ducting systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness
EN 598:2007+A1:2009 Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods
EN 14830:2006 Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance
EN 14758-1:2012 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
EN 14802:2005 Plastics piping systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading
EN 14636-2:2009 Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 2: Manholes and inspection chambers
EN 16323:2014 Glossary of wastewater engineering terms
EN 1671:1997 Pressure sewerage systems outside buildings
EN 1825-1:2004/AC:2006 GREASE SEPARATORS - PART 1: PRINCIPLES OF DESIGN, PERFORMANCE AND TESTING, MARKING AND QUALITY CONTROL
11/30245512 DC : 0 BS ISO 15398 - SPECIFICATIONS FOR THERMOPLASTICS COVERS AND FRAMES FOR MANHOLES AND INSPECTION CHAMBERS USED IN NON-TRAFFIC AREAS
PREN 1796 : DRAFT 2011 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP)
DIN EN 16397-2 E : 2015 FLEXIBLE COUPLINGS - PART 2: CHARACTERISTICS AND TESTING FOR METAL BANDED FLEXIBLE COUPLINGS, ADAPTORS AND BUSHES
DIN EN 14636-1:2010-04 Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints; German version EN 14636-1:2009
06/30154044 DC : 0 EN 12566-7 - SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 7: PREFABRICATED TERTIARY TREATMENT UNITS
I.S. EN 16932-3:2018 DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - PUMPING SYSTEMS - PART 3: VACUUM SYSTEMS
10/30217319 DC : 0 BS EN 13598-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS
DIN EN 16397-1:2015-01 FLEXIBLE COUPLINGS - PART 1: PERFORMANCE REQUIREMENTS
DIN EN 13598-2:2016-09 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS
DIN EN 14636-2:2010-04 Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 2: Manholes and inspection chambers
UNI EN 14636-2 : 2010 PLASTICS PIPING SYSTEMS FOR NON- PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS
I.S. EN 13476-1:2007 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY (VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS
EN 14364:2013 Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
I.S. EN 13598-2:2016 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS
17/30362689 DC : 0 BS EN 16941-2 - ON-SITE NON-POTABLE WATER SYSTEMS - PART 2: SYSTEMS FOR THE USE OF TREATED GREYWATER
15/30327636 DC : 0 BS EN 13476-3 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B
15/30327639 DC : 0 BS EN 13476-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A
I.S. EN 12566-6:2016 SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 6: PREFABRICATED TREATMENT UNITS FOR SEPTIC TANK EFFLUENT
BS EN 13598-2:2009 Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Specifications for manholes and inspection chambers in traffic areas and deep underground installations
DIN EN 13476-3:2015-11 (Draft) PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B
BS EN 1451-1:2017 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polypropylene (PP) Specifications for pipes, fittings and the system
I.S. EN 13476-2:2007 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY (VINYLCHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A
EN 13476-2:2018 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A
UNE-EN 16323:2014 Glossary of wastewater engineering terms
I.S. CEN TR 15128:2005 SURVEY OF EUROPEAN STANDARDS FOR REHABILITATION OF DRAIN AND SEWER SYSTEMS
DIN EN 13508-2:2011-08 Investigation and assessment of drain and sewer systems outside buildings - Part 2: Visual inspection coding system
DIN EN 1401-1:2009-07 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
DIN EN 12200-1:2016-10 PLASTICS RAINWATER PIPING SYSTEMS FOR ABOVE GROUND EXTERNAL USE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
DIN EN 1253-2:2015-03 GULLIES FOR BUILDINGS - PART 2: ROOF DRAINS AND FLOOR GULLIES WITHOUT TRAP
DIN EN 1253-4:2016-07 GULLIES FOR BUILDINGS - PART 4: ACCESS COVERS
DIN EN 13598-1 E : 2011 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS
I.S. EN 1401-1:2009 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
BS EN 1253-4:2016 Gullies for buildings Access covers
BS EN 14457:2004 General requirements for components specifically designed for use in trenchless construction of drains and sewers
BS EN 1825-1:2004 Grease separators Principles of design, performance and testing, marking and quality control
BS EN 1565-1:2000 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Styrene copolymer blends (SAN + PVC) Specifications for pipes, fittings and the system
BS EN 858-1:2002 Separator systems for light liquids (e.g. oil and petrol) Principles of product design, performance and testing, marking and quality control
BS EN 12566-1:2000 Small wastewater treatment systems for up to 50 PT Prefabricated septic tanks
EN 12200-1:2016 Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
EN 13564-1:2002 Anti-flooding devices for buildings - Part 1: Requirements
CEN/TR 15128:2005 Survey of European Standards for rehabilitation of drain and sewer systems
DIN EN 14802:2006-03 Plastics piping systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading
EN 1253-4:2016 Gullies for buildings - Part 4: Access covers
EN 13380:2001 General requirements for components used for renovation and repair of drain and sewer systems outside buildings
EN 1253-1:2015 GULLIES FOR BUILDINGS - PART 1: TRAPPED FLOOR GULLIES WITH A DEPTH WATER SEAL OF AT LEAST 50 MM
DIN EN 14457:2004-09 General requirements for components specifically designed for use in trenchless construction of drains and sewers
DIN EN 1825-1:2004-12 Grease separators - Part 1: Principles of design, performance and testing, marking and quality control; German version EN 1825-1:2004
DIN EN 274-1:2002-05 WASTE FITTINGS FOR SANITARY APPLIANCES - PART 1: REQUIREMENTS
UNE-EN 12666-1:2006 Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system
UNE-EN 14982:2007 Plastics piping and ducting systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness
UNE-EN 13508-2:2003 Conditions of drain and sewer systems outside buildings - Part 2: Visual inspection coding system

EN 681-4:2000/A2:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 4: CAST POLYURETHANE SEALING ELEMENTS
EN 14396:2004 Fixed ladders for manholes
EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
EN 681-3:2000/A2:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 3: CELLULAR MATERIALS OF VULCANIZED RUBBER
EN 805:2000 Water supply - Requirements for systems and components outside buildings
EN 14801:2006 Conditions for pressure classification of products for water and wastewater pipelines
EN 681-2:2000/A2:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 2: THERMOPLASTIC ELASTOMERS
EN 13380:2001 General requirements for components used for renovation and repair of drain and sewer systems outside buildings
EN 752:2017 Drain and sewer systems outside buildings - Sewer system management
EN 124:1994 Gully tops and manhole tops for vehicular and pedestrian areas - Design requirements, type testing, marking, quality control
EN 13101:2002 Steps for underground man entry chambers - Requirements, marking, testing and evaluation of conformity
EN 1085:2007 Wastewater treatment - Vocabulary
EN 14457:2004 General requirements for components specifically designed for use in trenchless construction of drains and sewers
ISO 48:2010 Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.