• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 7332/D7332M : 2016

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Measuring the Fastener Pull-Through Resistance of a Fiber-Reinforced Polymer Matrix Composite
Available format(s)

Hardcopy , PDF

Superseded date

08-11-2023

Language(s)

English

Published date

18-08-2016

1.1This test method determines the fastener pull-through resistance of multidirectional polymer matrix composites reinforced by high-modulus fibers. Fastener pull-through resistance is characterized by the force-versus-displacement response exhibited when a mechanical fastener is pulled through a composite plate, with the force applied perpendicular to the plane of the plate. The composite material forms are limited to continuous-fiber or discontinuous-fiber (tape or fabric, or both) reinforced composites for which the laminate is symmetric and balanced with respect to the test direction. The range of acceptable test laminates and thicknesses is defined in 8.2.

1.2Two test procedures and configurations are provided. The first, Procedure A, is suitable for screening and fastener development purposes. The second, Procedure B, is configuration-dependent and is suitable for establishing design values. Both procedures can be used to perform comparative evaluations of candidate fasteners/fastener system designs.

1.3The specimens described herein may not be representative of actual joints which may contain one or more free edges adjacent to the fastener, or may contain multiple fasteners that can change the actual boundary conditions.

1.4This test method is consistent with the recommendations of CMH-17, which describes the desirable attributes of a fastener pull-through test method.

1.5The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.5.1Within the text the inch-pound units are shown in brackets.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 30
DocumentType
Test Method
Pages
12
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 7745 : 2019 Standard Practice for Testing Pultruded Composites
ASTM D 4762 : 2018 Standard Guide for Testing Polymer Matrix Composite Materials

ASTM D 3171 : 1999 Standard Test Methods for Constituent Content of Composite Materials
ASTM E 177 : 1990 : REV A : R1996 Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
ASTM E 456 : 2002 Standard Terminology for Relating to Quality and Statistics
ASTM D 3878 : 2002 : REV A Standard Terminology for Composite Materials
ASTM E 456 : 2013 : REV A : R2022 Standard Terminology Relating to Quality and Statistics
ASTM D 3878 : 2015 Standard Terminology for Composite Materials
ASTM E 1434 : 2000 : R2013 Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases (Withdrawn 2015)
ASTM D 3878 : 2019 Standard Terminology for Composite Materials
ASTM D 3878 : 2000 Standard Terminology Composite Materials
ASTM D 3171 : 2011 Standard Test Methods for Constituent Content of Composite Materials
ASTM E 6 : 2002 Standard Terminology Relating to Methods of Mechanical Testing
ASTM E 456 : 2013 : REV A : R2017 : EDT 5 Standard Terminology Relating to Quality and Statistics
ASTM E 122 : 2017 : R2022 Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process
ASTM E 122 : 2017 Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process
ASTM D 3878 : 2003 : REV A Standard Terminology for Composite Materials
ASTM D 3878 : 2016 Standard Terminology for Composite Materials
ASTM E 1309 : 2000 Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases
ASTM D 3410/D3410M : 2016 Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading
ASTM D 3878 : 2019 : REV A Standard Terminology for Composite Materials
ASTM D 3878 : 2020 : REV A Standard Terminology for Composite Materials
ASTM D 3878 : 1998 Standard Terminology Composite Materials
ASTM D 3171 : 2022 Standard Test Methods for Constituent Content of Composite Materials
ASTM D 3410/D3410M : 2016 : EDT 1 Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading
ASTM D 3878 : 2018 Standard Terminology for Composite Materials
ASTM E 1434 : 2000 Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases
ASTM D 3171 : 2009 Standard Test Methods for Constituent Content of Composite Materials
ASTM D 3878 : 2002 Standard Terminology for Composite Materials
ASTM E 6 : 2015 : EDT 3 Standard Terminology Relating to Methods of Mechanical Testing
ASTM D 3878 : 2004 Standard Terminology for Composite Materials
ASTM E 4 : 2021 Standard Practices for Force Calibration and Verification of Testing Machines
ASTM D 3878 : 2007 : R2013 Standard Terminology for Composite Materials
ASTM E 1309 : 2000 : R2011 Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases (Withdrawn 2015)
ASTM D 3878 : 2020 : REDLINE Standard Terminology for Composite Materials
ASTM D 3878 : 2020 Standard Terminology for Composite Materials
ASTM D 3878 : 2003 Standard Terminology for Composite Materials
ASTM E 6 : 2015 : EDT 4 : REDLINE Standard Terminology Relating to Methods of Mechanical Testing
ASTM D 3878 : 2007 Standard Terminology for Composite Materials
ASTM D 3171 : 1999 : R2004 Standard Test Methods for Constituent Content of Composite Materials
ASTM E 1309 : 2000 : R2005 Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases
ASTM D 3171 : 2015 Standard Test Methods for Constituent Content of Composite Materials
ASTM E 456 : 2013 : REV A : R2017 : EDT 4 Standard Terminology Relating to Quality and Statistics
ASTM E 456 : 2013 : REV A : R2017 : EDT 6 Standard Terminology Relating to Quality and Statistics
ASTM D 3878 : 2004 : REV A Standard Terminology for Composite Materials
ASTM D 3171 : 2006 Standard Test Methods for Constituent Content of Composite Materials
ASTM E 1434 : 2000 : R2006 Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases
ASTM D 3878 : 2001 Standard Terminology Composite Materials

View more information
£69.29
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.