MIL C 15730 : M
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
COOLER, FLUID, NAVAL SHIPBOARD, LUBRICATING OIL, HYDRAULIC OIL, AND FRESH WATER
Available format(s)
PDF
Publisher
Superseded date
30-01-2024
Superseded by
£13.91
Excluding VAT
Covers lubricating oil, hydraulic oil and fresh water coolers for Naval shipboard applications.
| Committee |
FSC 4420
|
| DocumentType |
Standard
|
| Pages |
72
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
Superseded
|
| SupersededBy |
| MIL G 2145 : A NOTICE 1 | GENERATOR SET, GASOLINE ENGINE DRIVEN, DIRECT AND ALTERNATING CURRENT [NAVAL SHIPBOARD USE] |
| MIL-C-18419 Revision B:1962 | Compressors, Reciprocating, Motor Driven, Naval Shipboard High Pressure Air Service (No S/S Document) |
| MIL-E-17341 Revision C:1970 | Engine, Gas Turbine, Propulsion and Auxiliary Naval Shipboard |
| MIL-DTL-917 Revision F:2014 | Electric Power Equipment, Basic Requirements for |
| DOD-P-24562 Revision A:1982 | Propeller, Ship, Controllable Pitch (Metric) |
| MIL-G-24260 Base Document:1967 | Generator Set, Diesel Engine, 100 KW, 120-Volt Direct Current, 1800 RPM (No S/S Document) |
| MIL-T-17523 Revision D:1976 | Turbine, Steam, Auxiliary (and Reduction Gear) Mechanical Drive |
| MIL-G-22997 Revision A:1965 | Generator Set, Diesel Engine, 100 KW, 450-Volt A.C., 60-Cycle, 1800 R.P.M. (No S/S Document) |
| MIL-G-22077 Revision C:1993 | Generator Sets, Gas Turbine, Direct and Alternating Current Naval Shipboard Use |
| MIL-G-15788 Revision B:1964 | Generator Set, Diesel Engine 60 KW, 450 Volt A.C. 60 Cycle, 1800 RPM (No S/S Document) |
| MIL-C-23961 Revision A:1965 | Compressor, High Pressure Air, 100 CFM, Naval Shipboard Service (No S/S Document) |
| MIL G 24197 : NOTICE 2 | GENERATOR SET, DIESEL ENGINE 25O KW, ALTERNATING CURRENT |
| MIL-T-17286 Revision D:1989 | Turbines and Gears, Shipboard Propulsion and Auxiliary Steam; Packaging of |
| MIL E 917 : E | ELECTRIC POWER EQUIPMENT, BASIC REQUIREMENTS (NAVAL SHIPBOARD USE) |
| MIL-V-24439 Revision A:1984 | VALVE, OXYGEN, HELIUM AND HELIUM OXYGEN MIXTURE, HIGH PRESSURE FOR GAS SERVICES |
| MIL-W-21965 Revision D:1988 | Water Cooling of Shipboard Electronic Equipment General Specification for (Future Acquisitions may refer to MIL-HDBK-251, MIL-HDBK-2036, DOD-STD-1399-532 and S9086-SD-STM-010/532) |
| MIL-G-19287 Revision C:1961 | Generator Set, Steam Turbine, 2500 KW, 450 Volt, 60 Cycle, A.C. (No S/S Document) |
| MIL-G-22665 Base Document:1960 | Generator Set, Stream Turbine, 1500-KW, 450-Volt, 60-Cycle, A.C. (No S/S Document) |
| MIL-R-83248 Revision C:1994 | RUBBER, FLUOROCARBON ELASTOMER, HIGH TEMPERATURE, FLUID, AND COMPRESSION SET RESISTANT (S/S BY SAE-AMS7276, SAE-AMS7259, SAE-AMS3216, AND SAE-AMS3218) |
| ASTM A 569/A569M : 1998 | Standard Specification for Steel, Carbon (0.15 Maximum, Percent), Hot-Rolled Sheet and Strip Commercial (Withdrawn 2000) |
| MIL C 16173 : E | CORROSION PREVENTIVE COMPOUND, SOLVENT CUTBACK, COLD APPLICATION |
| ASME B1.12 : 1987 | CLASS 5 INTERFERENCE-FIT THREAD |
| MIL-E-15809 Revision D:1992 | Expander, Tube, Condenser and Heat Exchangers |
| MIL-STD-1186 Revision A:1981 | CUSHIONING, ANCHORING, BRACING, BLOCKING AND WATERPROOFING; WITH APPROPRIATE TEST METHODS (NO S/S DOCUMENT) |
| MIL-STD-2073-1 Revision E:2008 | Standard Practice for Military Packaging |
| ASME PV CODE 8 DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1 |
| DOD-STD-1399-301 Revision A:1986 | INTERFACE STANDARD FOR SHIPBOARD SYSTEMS SECTION 301A SHIP MOTION AND ATTITUDE (METRIC) |
| MIL R 6855 : E | RUBBER, SYNTHETIC, SHEETS, STRIPS, MOLDED OR EXTRUDED SHAPES |
| MIL-A-19521 Revision B:1992 | Anode Retaining Support Plugs and Anode Selection and Installation Design Criteria for Shipboard Condensers and Heat Exchangers |
| ASTM A 516/A516M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service |
| ASTM B 584 : 2014 : REDLINE | Standard Specification for Copper Alloy Sand Castings for General Applications |
| MIL S 1222 : H | STUD, BOLTS, HEX CAP SCREWS, SOCKET HEAD CAP SCREWS AND NUTS |
| MIL-P-24691-1 Base Document:1987 | Pipe And Tube, Carbon Steel, Seamless |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| MIL A 18001 : K | ANODES, SACRIFICIAL ZINC ALLOY |
| MIL P 15024 : E | PLATES, TAGS AND BANDS FOR IDENTIFICATION OF EQUIPMENT |
| MIL-L-19140 Revision E:1984 | Lumber and Plywood, Fire-Retardant Treated |
| MIL-STD-438 Revision E:1973 | Schedule of Piping, Valves, Fittings, & Associated Piping Components for Submarine Service |
| MIL-G-21610 Revision C:1989 | Gaskets, Heat Exchanger, Various Cross Section Rings, Synthetic Rubber |
| MIL C 24707/1 : 0 | CASTINGS, FERROUS, FOR MACHINERY AND STRUCTURAL APPLICATIONS |
| MIL G 24696 : B | GASKET, SHEET, NON-ASBESTOS |
| MIL-B-24480 Revision A:1985 | Bronze, Nickel-Aluminum (UNS No. C95800) Casting for Seawater Service |
| MIL-T-15005 Revision F:1989 | TUBES, CONDENSER AND HEAT EXCHANGER, COPPER-NICKEL ALLOYS (UNS C70600 & C71500) |
| ASTM B 61 : 2015 : REDLINE | Standard Specification for Steam or Valve Bronze Castings |
| MIL-STD-777 Revision F:2012 | Schedule of Piping, Valves, Fittings, and Associated Piping Components for Naval Surface Ships |
| MIL-STD-278 Revision F:1987 | WELDING AND CASTING STANDARD (REPLACEMENT DOCUMENT NAVSEA TECH PUB S9074-AR-GIB-010/278) |
| MS16142 Revision C:1979 | BOSS, GASKET SEAL STRAIGHT THREAD TUBE FITTING, STANDARD DIMENSIONS FOR (S/S BY SAE-J1926/1 AND ISO725) |
| MIL-L-24478 Revision C:1990 | Lubricant, Molybdenum Disulfide in Isopropanol |
| MIL-T-22214 Revision C:1993 | Tube, Condenser and Heat Exchanger with Integral Fins (UNS Alloy Nos. C17500, C70600, C12200) |
| MIL-STD-1627 Revision C:1994 | Bending of Pipe or Tube for Ship Piping Systems |
| MIL S 901 : D | SHOCK TESTS, HI [HIGH IMPACT] SHIPBOARD MACHINERY, EQUIPMENT AND SYSTEMS, REQUIREMENTS FOR |
| ASTM B 209 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
| MIL N 24106 : C | NICKEL-COPPER ALLOY BARS, RODS AND FORGINGS |
| MIL-P-116 Revision J:1988 | PRESERVATION, METHODS OF (S/S BY MIL-STD-2073-1) |
| FF-W-84 Revision A:1967 | Washers, Lock (Spring) |
| ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| ASTM B 43 : 2015 : REDLINE | Standard Specification for Seamless Red Brass Pipe, Standard Sizes |
| MIL-P-15024-5 Base Document:1971 | Plate, Identification |
| MIL G 1149 : C | GASKET MATERIAL, SYNTHETIC RUBBER, 50 AND 65 DUROMETER HARDNESS |
| TT-P-645 Revision C:2013 | Paint, Alkyd Type, Formula Number 84 |
| ASTM A 515/A515M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service |
| MIL-P-83461 Revision B:1980 | PACKING, PREFORMED, PETROLEUM HYDRAULIC FLUID RESISTANT, IMPROVED PERFORMANCE AT 275 DEG. F (135 DEG. C) (S/S BY SAE-AMS-P-83461) |
| FED-STD-H28 Revision A:1994 | Screw-Thread Standards for Federal Services |
| MIL-T-24107 Revision B:1987 | Tube, Copper (Seamless) (Copper Alloy Numbers C10100, C10200, C10300, C10800, C12000, C12200, and C14200) |
| MIL-STD-22 Revision D:1979 | WELDED JOINT DESIGN |
| MIL-L-24479 Revision C:1990 | Lubricant, Red Lead and Graphite in Mineral Oil (No S/S Document) (for Future Acquisition of a Product with Similar Functional Performance Refer to A-A-59004) |
| MIL A 907 : E | ANTISEIZE THREAD COMPOUND, HIGH TEMPERATURE |
| ASTM B 248 : 2017 : REDLINE | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar |
| MIL-C-15726 Revision F:1988 | Copper-Nickel Alloy, Sheet, Plate, Strip, Bar, Rod and Wire |
| ASTM A 285/A285M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength |
| ASTM B 122/B122M : 2016 : REDLINE | Standard Specification for Copper-Nickel-Tin Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar |
Summarise
£13.91
Excluding VAT
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.